INSTALLATION INSTRUCTIONS FOR PART 99-8714
APPLICATIONS
SMART FORTWO
2008
99-8714
KIT FEATURES
• DIN Radio Provision with Pocket
• Stacked DIN Units Provision
KIT COMPONENTS
A) Radio Housing • B) Pocket
A
B
TOOLS REQUIRED:
• Small Flat Blade Screwdriver/ Panel Removal Tool
• T-20 Torx Screwdriver
1-800-221-0932
© COPYRIGHT 2008 METRA ELECTRONICS CORPORATION
99-8714 DASH DISASSEMBLY
SMART FORTWO 2008
A
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
3
4
Unclip the Hazard button switch panel.
(Figure A)
Remove (1) T-20 Torx head screw.
(Figure B)
Carefully unclip the panel surrounding
the radio, start at the top of the dash
and work your way down. (Figure C)
B
5
6
Remove (4) T-20 Torx head screws
from around the radio. (Figure D)
Disconnect the wire harness and
antenna and remove radio.
Continue to kit assembly.
C
D
1
99-8714 KIT ASSEMBLY
DIN RADIO PROVISION WITH POCKET
Note: Refer also to the instructions included with the aftermarket radio.
A
1
2
3
Slide the DIN cage into the radio
housing and secure by bending the
metal locking tabs outward. (Figure A)
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure B)
Snap the pocket into the radio hous-
ing. (Figure C)
Continue to final assembly.
B
NOTE: Pocket may be installed in top
or bottom of radio housing.
C
2
99-8714 KIT ASSEMBLY
STACKED DIN UNITS PROVISION
Note: Refer also to the instructions included with the aftermarket radio.
A
1
2
Slide the DIN cages into the radio
housing and secure by bending the
metal locking tabs outward. (Figure A)
Slide the aftermarket units into the
cage until it snaps into place.
(Figure B)
Continue to final assembly.
B
3
99-8714 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
99-8714
NOTES
5
99-8714 INSTRUCTIONS
1-800-221-0932
REV. 03/27/08 © COPYRIGHT 2008 METRA ELECTRONICS CORPORATION INST99-8714
|