ECHNICAL INFORMATION
PRODUCT
T
P 1/ 4
Models No.
Description
DF030D (FD01*)
L
10.8V Cordless Driver Drill
* Model number for North and Central American
countries except Mexico and Guam
H
W
CONCEPT AND MAIN APPLICATIONS
Model DF030D is a 10.8V cordless driver drill compact and lightweight
for easy handling, but featuring 2-speed gear selection with variable speed
in each range for a wide range of applications.
Dimensions: mm (")
Length (L) 157 (6-3/16)
Width (W)
53 (2-1/16)
Uses new 10.8V Li-ion battery of stick type as a power unit.
Height (H) 183 (7-1/4)
This product is available in the following variations.
Battery
type
Plastic
carrying case
Housing
color
Model No.
Charger
Offered to
quantity
2
Makita-blue
white
Makita-blue
white
DF030D
USA, Canada
Mexico, Panama
DF030DW
DF030DWE
DF030DWEW
BL1013
(Li-ion 1.3Ah)
DC10WA
Yes
All countries except
the four listed above
The models also includes the accessories listed below in "Standard equipment".
Specification
Type of cell
Li-ion
10.8
Voltage: V
Battery
Capacity: Ah
1.3
50
Charging time (approx.): min.
with DC10WA
Max. output: W
115
0 - 350
0 - 1,300
6.35 (1/4) Hex
10 (3/8)
Low
High
No load speed: min-1 = rpm
Driving shank: mm (")
Capacities: mm (")
Steel
Wood
21 (13/16)
Max. fastening torque:
N.m (in.lbs)
Soft joint
Hard joint
14 (120)
24 (210)
Torque adjustment
18 stages + drill mode
0.5 - 3.5 (4 - 30)
Clutch torque setting: N.m (in.lbs)
Lock torque: N.m (in.lbs)
Electric brake
22 (200)
Yes
Variable speed control by trigger
Mechanical 2-speed
Yes
Yes
Reverse switch
Yes
LED job light
Yes
Net weight [with battery BL1013]: kg (lbs)
0.88 (1.9)
Standard equipment
Phillips bit 2-50 (double-end) ........ 1 pc (for countries using M-type spindle)
Phillips bit 2-45 (double-end) ........ 1 pc (for countries using N-type spindle)
Holster ............................................ 1 pc
Note: The standard equipment for the tool shown above may differ by country.
Optional accessories
Driver bits, Socket bits, Hex shank drill bits for wood, Hex shank drill bits for steel, Bit piece,
Drill chuck, Charger DC10WA, Battery BL1013
P 2/ 4
Repair
CAUTION: Remove the bit and the battery from the machine for safety before
repair/ maintenance in accordance with the instruction manual!
[1] NECESSARY REPAIRING TOOLS
Code No.
1R291
Description
Use for
Retaining ring S and R pliers
Removing/ Installing Bit sleeve
[2] DISASSEMBLY/ASSEMBLY
[3]-1. DC Motor, Gear Assembly, Speed Change Lever Assembly
DISASSEMBLING
Fig. 1
Set plate
(2pcs.)
1) Remove two Set plates with which Handles (L) and (R) are assembled to one
another as follows:
Insert a small slotted screwdriver through the punched hole of Set plate and
move Set plate in the direction of the arrow using the screwdriver. (Fig.1)
2) Remove Housing (R) from Housing (L) by loosening six Bind PT3x6 tapping
screws.
Handle (R)
3) Remove Speed change lever assembly from Gear assembly. (Fig. 2)
4) Remove DC motor from Gear assembly as illustrated in Fig. 3
5) Separate DC motor from Bracket by loosening two M3x6 Pan head screws.
(Fig. 4)
small slotted
screwdriver
Handle (L)
Fig. 2
Speed change lever assembly
Fig. 3
Fig. 4
Shift the change lever of Gear
assembly to the high speed position.
M3x6 Pan head screws
(2pcs.)
1
change lever of
Gear assembly
Motor bracket
Turn Gear assembly
counterclockwise.
2
3 Pull out Gear assembly
from DC motor with
Bracket.
convex portion of
Motor bracket
DC motor
DC motor
ASSEMBLING
Fig. 5
1) Fix Motor bracket to DC motor with two M3x6 Pan head screws.
Note: Align the red marking on DC motor with non-convex portion of
Motor bracket. (Fig. 5)
non-convex portion
2) Fix Gear assembly to DC motor with bracket and turn Gear assembly
clockwise.
Note: Align the change lever of Gear assembly with the red marking on
DC motor. (Fig. 3)
red marking on
terminal of positive
pole
3) Fix Speed change lever assembly to the change lever of Gear assembly as
illustrated in Fig. 2.
Note: Set the change lever of Gear assembly in place between two
Compression springs 4 on the reverse side of Speed change lever
assembly, and insert the emboss of the change lever into one of
Compression spring 4. (Fig. 6)
convex portions
Fig. 6
change lever of
Gear assembly
Viewed from the upper position
Speed change lever assembly
Emboss of change lever
of Gear assembly
Compression spring 4
P 3/ 4
Repair
[2] DISASSEMBLY/ASSEMBLY
[3]-1. DC Motor, Gear Assembly, Speed Change Lever Assembly (cont.)
ASSEMBLING
(4) After installing the assembled parts in place of Housing L, shift Speed change lever assembly to either low speed
position or high speed position.
(5) Fixing Housing (R) to Housing (L) with six Bind PT3x16 tapping screws.
(6) Insert two Set plates in place. (Fig. 1)
[3]-2. Disassembling Bit Holder of Gear Assembly
Fig. 7
Ring spring 10
(1) While pushing the top of sleeve by your thumb to prevent Compression spring 13
from popping out from Bit holder, expand Ring spring 10 using 1R291 and raise
the opposite of the expanded Ring spring 10 by your index finger. (Fig. 7)
(2) Ring spring 10 can be removed.
And Flat washer 11, Compression spring 13, Bit sleeve and Steel ball 3 (2pcs.)
can be removed.
1R291
Sleeve
[3]-3. Assembling Leaf Spring
Set Leaf spring in place. (Fig. 8)
Fig. 8
Note: Do not face the center edge of Leaf spring to Housing L.
Leaf spring
center edge
Housing L
Fig. 9
[3]-4. Assembling F/R Change Lever
Link the notch of F/R change lever and the protrusion of Switch,
then install them in Housing L. (Fig. 9)
notch of F/R change lever
protrusion of Switch
Circuit diagram
Fig. D-1
red marking
DC motor
Color index of lead wires' sheath
＋
＋
M1
M2
Black
Red
Terminal
Switch
White
－
－
LED
P 4/ 4
Wiring diagram
Fig. D-2
Pay attention to the directions of lead wires and connect Flag receptacles
to electrical parts.
Refer to the following illustration.
red marking
Terminal
DC motor
Fig. D-3
Before installing Switch in Housing R, route Lead wires as illustrated below and connect two Connectors.
Do not ride their Lead wires on ribs.
Lead wire holders
Connector
(To Switch)
Connector
LED
Lead wires in this area
must be tight.
Fig. D-4
Bend the terminals of DC motor
as illustrated.
Route Lead wires between ribs.
Insert Connectors between
their Lead wire holders.
Flag receptacles and
Lead wires have to
be far from DC motor.
Do not ride them
on the ribs.
Face the glue-attached portion of LED
to DC motor side.
Lead wires holders
Do not ride Lead wires on their embosses.
|