Lytecaster® Recessed Downlighting 1004SIC
®
Page 1 of 1
5" Aperture 0 Shallow Incandescent Convertible IC/Non-IC Frame-in Kit
1004SICN
(Integral Nail)
Overall Length
1004sic/N: 9"
1004SIC
(Integral Screw)
7
1
Frame-In Kit
Overall Width
1004sic/n: 5 3/4”
13" MIN.
24" MAX.
2
6
Top View
3
5
Reflector Trim
Height
1004sic/n: 5 1/2"
4
Ceiling Opening: 5 3/8" Diameter
5" Aperture: Complete Fixture consists of Reflector Trim & Frame-In Kit. Select each separately.
Frame-In Kit
Reflector Trims — See Individual Reflector Trim Specification Sheets
Open Downlight
Cone
Satin Cone
Baffles
Basic White
Wall Washer
Enclosed Diffuser
1004SIC
1012
1008
1005
1071
1085*
1024*
1004SICN
1012NM
1013
1008NM
1010
1010NM
1005WH
1005NM
1005BNM
1076
1013WH
1013CD
1013NM
1013BKNM
1013CDNM
1013BK
1076WH
*for Non-IC applications only
Feature
Options & Accessories
1. Housing: .032” (#20 ga.) Aluminum. UL listed convertible IC/NON-IC. 2"
vertical adjustment in ceiling. Can be removed for access to junction box and
ceiling plenum. 5 1/2" tall for use in 2" X 6" joist construction and shallow
plenum applications. AirSeal® housing minimizes air leakage to less than 2
CFM at 1.57 PSF (or 75pa), which complies with Model Energy Code (Section
602.3.3) and Washington State Energy Code (Section 502.4) and reduces heat
loss and condensation in ceiling.
AirSeal® Kit:
LAS56
NOTE: Use only if factory installed tape or knockouts are removed from vertical
adjustment slots in housing wall.
Labels
UL (Type IC/NON-IC Convertible, Suitable for Damp Locations)
Complies with Air Leakage Requirements stated in the Model Energy Code and
the Washington State Energy Code.
2. Mounting Frame: .048" (#18 ga.) galvanized steel. Locks into position along
length of mounting bars with locking spring and bendable slot. (3) slots 90°
apart simplify alignment.
3. Junction Box: 2" X 4" X 3 1/2" (22 cu. in.) .032" (#22 ga.) galvanized steel.
UL listed for maximum of 8 (#12 ga.) 1104SIC/N and 6 (#12 ga.) 1004SIC/N
90°C through branch circuit conductors. Integral cable clamps permit
attachment of non-metallic (#12 or #14 ga.) Romex® cable without tools or
additional connectors.
AirSeal® is a registered trademark of Lightolier.
Romex® is a registered trademark of General Cable Industries Inc.
Job Information
Type:
4. Mounting Bars: .059" (#16 ga.) galvanized steel. Bars pivot for easy
attachment and wire-in below ceiling line. Bars extend to accommodate
16" to 24" O.C. joist spacing. Bars can accommodate 9" O.C. joist spacing
after a slight field modification (See Instruction Sheet). 1004SIC features
integral self-tapping phillips screws for secure attachment to wood or metal
construction. The 1004SICN features integral nails for secure attachment to
wood. Both attach to T-bar ceilings without the need of accessories.
5. Socket Housing: Impact extruded aluminum or galvanized steel. Attached
trim retaining spring secures trim to any height on housing wall.
6. Socket: Porcelain medium base; nickel plated screw shell. Pre-wired with
#18 ga. SF1 (300 Volt 200° C) leads to junction box.
Job Name:
Cat. No.:
Lamp(s):
Notes:
7. Thermal Protector: Meets NEC and UL requirements. Located inside
housing.
Lightolier a Genlyte company
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2006 Genlyte Group LLC • I0806
|