LevelOne
User Manual
KVM-0213
2-Port PS/2 Cable KVM Switch
Ver. 1.0.0-0803
Installation
Important
1. Before you begin, make sure that the power to all the devices you will be connecting has
been turned off. You must unplug the power cords of any computers that have the
Keyboard Power On function. Otherwise, the switch will receive power from the computer.
2. To prevent damage to your equipment, make sure that all the devices you will be
connecting are properly grounded.
Installing your new KVM-0213 involves the following steps:
1. Plug your keyboard, monitor, and mouse into the Console ports on the KVM-0213. Each
port is labeled with an appropriate icon.
2. Plug your speakers into the KVM-0213’s speaker jack. *This step is optional
3. Plug the attached KVM cables’ keyboard, monitor, mouse, and speaker connectors into
their respective ports on the computers you are installing.
After you have finished attaching the cables, turn on the power to the computers.
Note: The KVM-0213’s Power On default is to link to the first computer you turn on.
Operation
Hotkey Port Selection
All hotkey port switches begin with tapping the Scroll Lock key twice.
[Scroll Lock] [Scroll Lock]
Invokes Auto Scan Mode
Starts Auto Scan. Press and release the [Left Shift] key, and then press the [Right Shift] key.
[Left Shift] [Right Shift]
Scan Interval
Sets the Auto Scan interval to n second intervals - where n is a number from 1 – 4.
[Left shift] [Right shift] [S] [n]
The n stands for the number of seconds that the focus dwells on a port
before switching to the other one. Replace the n with a number
between 1 and 4 when entering this hotkey combination. (See the
table, below.)
Scan Interval Table
n
1
2
3
4
Sec.
3 Sec.
5 Sec. (Default)
10 Sec.
20 Sec.
Troubleshooting
Symptom
Possible Cause
Action
Keyboard Not Responding
Keyboard needs to be reset. Unplug the keyboard from
the Console
Keyboard Port, then plug it
back in.
Switch needs to be reset.
Turn off the computers.
Unplug the KVM cables. Wait
five seconds; then plug the
cables back in and turn the
computers on.
Pressing Hot Keys Gets No
Response
Hotkey sequence input
incorrectly.
Resend the Hotkey
command – press and
release each key in the
sequence individually.
Unplug the mouse from the
Console
Mouse Not Detected, or
Mouse needs to be reset.
Does Not Respond Correctly
Mouse Port, then plug it back
in.
Video Problems
Resolution and/or
Select a lower resolution
and/or bandwidth.
Bandwidth set too high.
Specifications
Function
Computer Connections
Port Selection
KVM-0213
2
Hotkey
Keyboard
Video
Mouse
1 x 6-pin Mini-DIN Female (Purple)
1 x HDB-15 Female (Blue)
1 x 6-pin Mini-DIN Female (Green)
1 x Mini Stereo Jack Female (Green)
Console
Ports
Speaker
Keyboard
Video
2 x 6-pin Mini-DIN Male (Purple)
2 x HDB-15 Male (Blue)
Connectors
KVM
Ports
Mouse
2 x 6-pin Mini-DIN Male (Green)
Speaker
2 x Mini Stereo Plug Male (Green)
2 (Green)
LEDs
Selected
Cable
Length
Computers
1.2m
Emulation
Video
Scan Interval
Keyboard/ Mouse
PS/2
2048 x 1536; DDC2B
3, 5, 10, 20 Seconds
0-50°C
Operating Temp.
Storage Temp.
Humidity
Environment
-20-60°C
0-80% RH, Non-condensing
Plastic
Housing
Weight
0.41 kg
Physical
Properties
Dimensions
(L x W x H)
8.1 x 6.3 x 2.35 cm
|