HCS6600 CodePlus™ Series
Cable HD Transcoder
MPEG-2
Installation & Setup Guide
Warranty
Part No: 206-4119
© Copyright 2010, LG Electronics U.S.A., Inc.
IMPORTANT SAFETY INSTRUCTIONS
Important safeguards for you and your new product
THIS PRODUCT HAS BEEN MANUFACTURED AND TESTED WITH SAFETY IN
MIND. IMPROPER USE, HOWEVER, CAN RESULT IN POTENTIAL ELECTRICAL
SHOCK OR FIRE HAZARDS. TO AVOID DEFEATING THE SAFEGUARDS THAT
HAVE BEEN BUILT INTO THIS PRODUCT, PLEASE READ AND OBSERVE THE
FOLLOWING SAFETY POINTS WHEN INSTALLING AND USING THIS PRODUCT.
1. Read these instructions.
9. Outdoor Use
Warning: To prevent fire or shock
Read all the safety and operating instructions
before operating the product.
hazards, do not expose this product
to rain or moisture.
2. Keep these instructions.
Retain the safety and operating instructions
for future reference.
10. Wet Location
The apparatus shall not be exposed to drip-
ping or splashing and no objects filled with
liquids, such as vases, shall be placed on
the apparatus.
3. Heed all warnings.
Adhere to all warnings on the product and in
the operating instructions.
11. Test Equipment
4. Follow all instructions.
In some cases, LG has supplied or recom-
mended the use of test equipment and
devices for the setup and testing of the
equipment. The operation and maintenance
of test equipment is described in their asso-
ciated instruction manuals. Please refer to
these manuals for explicit instructions
regarding the safe use and handling of the
equipment.
Follow all operating and use instructions.
5. Do not use this apparatus near water.
Do not use this product near water or mois-
ture or in an area, such as a basement, that
might become flooded.
6. Clean only with dry cloth.
Unplug this product before cleaning. Do not
use liquid cleaners or aerosol cleaners.
12. Replacement Parts
7. Refer all servicing to qualified service per-
sonnel.
When replacement parts are required, be
sure the service technician uses replace-
ment parts specified by the manufacturer or
that have the same characteristics as the
original parts. Unauthorized substitutions
may result in fire, electric shock, or other
hazards.
Servicing is required when the apparatus has
been damaged in any way, liquid has been
spilled or objects have fallen into the appara-
tus, the apparatus has been exposed to rain
or moisture, does not operate normally, or
has been dropped.
8. Object and Liquid Entry
Never push objects of any kind into this prod-
uct through openings as they may touch dan-
gerous voltage points or short-out parts that
could result in a fire or electric shock. Never
spill liquid of any kind on the product.
(Continued on next page)
206-4119
3
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
14. Servicing
Caution: These servicing instruc-
13. Damage Requiring Service
tions are for use by qualified
service personnel only. To reduce
the risk of electrical shock, do not per-
form any servicing other than that
described in the operating instructions
unless you are qualified to do so.
Unplug this product from the wall power out-
let and refer servicing to qualified service
personnel under the following conditions:
a. If liquid has been spilled, or objects have
fallen into the product.
15. Safety Check
b. If the product has been exposed to rain or
water.
Upon completion of any service or repairs to
this product, ask the service technician to
perform safety checks to determine that the
product is in proper operating condition.
c. If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operating instructions, as an improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore
the product to its normal operation.
d. If the product has been dropped or the
cabinet has been damaged.
e. If the product exhibits a distinct change in
performance.
Caution: Refer all servicing to qualified
service personnel.
206-4119
4
Table of Contents / Setup Information
Table of Contents
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safety Instructions. . . . . . . . . . . . 34
Table of Contents / Setup Information. . . . . . . 5
HCS6600 Product Description . . . . . . . . . . . . 6
Transcoder Product Description . . . . . . . . . . . 7
Card Description . . . . . . . . . . . . . . . . . . . . . . . 8
Installing CodePlus Transcoder Cards. . . . . . . 9
Cable TV STB Receiver & HCS6600
Initialization & Setup Connections . . . . . . . . . 10
System Setup . . . . . . . . . . . . . . . . . . . . . .1112
Configuration Options . . . . . . . . . . . . . . . 1315
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . 16
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 17
Document Revision History / Notes . . . . . . . 18
Warranty . . . . . . . . . . . . . . . . . . . . . Back Cover
Setup Information
This document provides installation and setup support only for an HCS6600 transcoder card. Cable
TV service and a Cable TV STB receiver must be installed and operating before you can proceed to
set up the HCS6600. LG recommends that the system be professionally installed.
Check the items listed below before you begin the HCS6600 installation and setup procedures.
Cable Set-top Box (STB)
HCS6600
__ Refer to the documentation provided with the
Cable TV STB, and carefully follow the sys-
tem setup procedures. (The Cable TV STB
receiver provides the IEEE-1394 signal input
for the HCS6600.)
__ If the HCS6600 will be used with a unique
feature card (Example: HCS6300) in the
card frame CONTROLLER slot, you will also
need a copy of the Installation & Setup
Guide for the feature card in order to com-
plete the HCS6600 system setup.
__ Authorization is required for HD channels.
Contact your local Cable TV provider to get
subscription programming authorization for
the Cable TV STB receiver.
__ For HCS6600 Service Port connections, you
must use an FTDI TTL-USB cable (P/N TTL-
232R-5V-AJ).
ASI Output (Optional)
__ If applicable, install the DTV modulator and
upconverter that will receive the ASI output
signal from the HCS6600. Refer to the man-
ufacturer's documentation.
206-4119
5
HCS6600 Product Description
The HCS6600 is one of the LG CodePlus™ series of transcoder cards. Pairing an HCS6600 card, in
the appropriate CodePlus card frame, with a suitable Cable TV STB receiver will provide one chan-
nel of Cable TV content.
Features
• Part of modular system, easily scaled for each application
• Transcodes Cable DTV content to ATSC-compatible MPEG-2
®
• Built-in Pro:Idiom content protection
• DVB-ASI output available to connect to external MUX or modulator
• Transcoded output supports Closed Captions and V-Chip (Parental Control) *
• Short 3U height profile to minimize rack-space usage
HCS6600
SERVICE
PORT
RESET
STATUS
1
I
E
E
E
39
4
B
1
3
9
4
A
I
E
E
E
ASI OUT
* If included in the signal source.
206-4119
6
Transcoder Product Description
Typical Cable HD Transcoder System Overview
The LG HCS6600 Cable HD transcoder represents a single-channel HDTV solution for commercial
and institutional MATV systems (hotels, hospitals, etc.).
A typical Cable HD Transcoder system includes:
• An HCS6600 Cable HD transcoder for each HD program offered in the commercial facility MATV
system.
• A CodePlus series card frame (Example: HCS6100R) specified for the HCS6600.
Purchased separately:
• Cable TV service feed.
• Cable TV STB receiver for each transcoder/HD program.
• VSB or QAM modulator with ASI input (for each transcoder) or LG CodePlus-series unique feature
card (Example: HCS6300). Multiplexers can be used in front of the modulator if multiple programs
are desired and 256-QAM is used.
• (For each modulator, if applicable) Upconverter compatible with digital modulation.
• 19-inch rack for mounting.
• Miscellaneous cables and installation hardware (see also HCS6600 setup information on page 5).
The elements of such a system combined can:
• Receive a selected HD channel from Cable TV service using a Cable TV STB receiver.
• Transcode the digital video and audio stream to an ATSC A/53E compatible transport stream.
• Encrypt the received digital data stream.
• Modulate the stream in 64-QAM or multiplexed 256-QAM.
A Pro:Idiom-compatible television with a QAM/VSB tuner is required to view premium HD content.
The HCS6600 changes the Cable TV encryption scheme to a Pro:Idiom encryption scheme. A proper
session ID must be set at the TV in order for Pro:Idiom decryption to be enabled. LG’s Pay-Per-View
(PPV) partners can properly set up this session through their interface. An LG Free-to-Guest (FTG)
card is substituted for the supplied Multiple Protocol Interface (MPI) card and can set the session to
allow decryption.
Note: Design and specifications subject to change without prior notice.
206-4119
7
Card Description
Retaining Screw
Install after inserting
HCS6600 card
HCS6600
Service Port
SERVICE
TTL-USB serial port
connection (use FTDI
TTL-232R-5V-AJ cable)
PORT
RESET
STATUS
1
Reset
Reboots card
I
IEEE-1394 In
To Cable TV STB
1394 Out
39
4
B
E
E
E
Note: Always use
the IEEE-1394A port
for the Cable TV
STB connection.
Status
Blinking pattern indicates
condition of card
1
3
9
4
A
I
E
E
E
ASI Out
DTV signal output
ASI OUT
Retaining Screw
Install after inserting
HCS6600 card
206-4119
8
Installing CodePlus Transcoder Cards
Slots
3 & 4
CONTROLLER
Slot
HCS6600
Slot 1 Slot 2
Slot 7 Slot 8 Slot 9 Slot 10 Slot 11 Slot 12
Slot 5 Slot 6
HCS6600
HCS6600
HCS6600
HCS6300
HCS6600
HCS6600
HCS6600
HCS6600
HCS6600
HCS6600
SERVICE
PORT
ETHERNET
SERVICE
PORT
SERVICE
PORT
SERVICE
PORT
SERVICE
PORT
SERVICE
PORT
SERVICE
PORT
SERVI
PORT
SERVICE
SERVICE
PORT
PORT
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
1
3
9
4
B
1
3
9
4
B
1
3
9
4
B
1
3
9
4
B
1
3
9
4
B
1
3
9
4
B
1
3
9
4
B
1
3
9
4
B
1
3
9
4
B
I
I
I
I
I
I
I
I
I
SERVICE
PORT
1
I
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
39
4
B
E
E
E
RESET
1
3
9
4
A
1
3
9
4
A
1
3
9
4
A
1
3
9
4
A
1
3
9
4
A
1
3
9
4
A
1
3
9
4
A
1
3
9
4
A
1
3
9
4
A
I
I
I
I
I
I
I
I
I
STATUS
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
1
3
9
4
A
I
RF OUT
E
E
E
ASI OUT
ASI OUT
ASI OUT
ASI OUT
ASI OUT
ASI OUT
ASI OUT
ASI OUT
ASI OUT
ASI OUT
CONTROLLER Slot
The card in this slot may vary
depending on system features.
Note: All cards used in the card frame
must be inserted and removed by
qualified service personnel only.
1. Unpack the HCS6600 unit(s) and all accessories.
Accessories provided: IEEE-1394 Cable
(Length = 1 meter)
Note: Use extreme care when handling an
HCS6600 card. Always observe proper
precautions with respect to static electric-
ity and mechanical shock. When not installed
in a card frame, return the HCS6600 card to the
anti-static bag in which it was shipped.
2. Select the slot(s) in the card frame in which to
install the HCS6600. Note: All cards must be
used in an LG-approved card frame for this
product.
3. Remove the AC power cord for the card frame
from the power outlet.
Note: The CodePlus series products are
NOT designed to be hot-swappable!!!
Power must be removed to the card
frame before any CodePlus transcoder cards
are inserted or removed.
4. Remove the blank cover plate from each slot
into which a card is to be inserted.
5. Without using force, slide each new card into
its designated slot, and ensure that it is fully
inserted.
Note: The card slots in the card frame
are NOT all identical!!! An HCS6600 card
can only be installed in Slots 1 to 6 and
7 to 12. The CONTROLLER slot between Slots
6 and 7 is dedicated for optional feature cards
and is not compatible with HCS6600 cards.
6. Engage and tighten the top and bottom
thumbscrews securely. Note that the thumb-
screws should only be finger tight; overtighten-
ing may damage the assembly.
Note: When installing cards, remove
blank cover plates and insert new cards
as applicable. For ports that will not be
used, leave the blank cover plates in place
for proper ventilation and FCC and safety
agency compliance.
7. Refer to the diagram on page 10 for cable
connections, and complete the system instal-
lation and test procedure on page 11.
206-4119
9
Cable TV STB Receiver & HCS6600
Initialization & Setup Connections
Laptop
PC
RF Feed
Cable TV
STB
from Cable TV
Provider
. . . . .
. . . . .
Power Outlet
TELLITE IN
SA
SW1
(120V 60Hz AC)
1
3
9
4
.
.
.
.
.
.
)
Y
LAN
VICE ONL
(SER
TTL-USB
Service Port
Connection
R
-
UDIO
-A
O
L/MONO
V
A
VIDEO
HCS6600
In Card Frame
Chassis
Composite
Video
1394
Link
and L/R Audio
to NTSC Monitor
HCS6600
HCS6600
HCS
SER
VICE
PO
RT
RES
ET
ST
A
TUS
1
3
9
4
B
I
E
E
E
T
SER
POR
RESE
ik
T
T
1
3
9
4
B
I
E
E
E
VICE
1
3
9
4
A
I
E
E
E
C
t
600
1
3
9
4
A
I
E
E
E
P
T
t
HCS6600
u
o
HCS660
0
t
SER
POR
RESE
T
VICE
HCS6600
I
1
3
X
4
B
I
I
t
t
T
AS
I
OU
T
SER
VI
CE
POR
ST
T
HCS6600
I
ST
A
T
A
TU
S
R
E
SER
POR
I
E
E
E
SE
TUS
T
VICE
ST
TUS
A
T
E
E
E
1
3
9
4
B
RESE
I
E
E
E
SER
VI
POR CE
T
R
ESE
T
I T
X
X
ST
A
T
US
1
I
SE
RVI
9
X
3
T
C
E
I
E
E
E
E
P
O
X
ST
A
R
T
X
9
TUS
1
3
9
4
B
R
ESE
R
E
4
B
I
E
E
E
T
1
3
9
4
A
X
I
E
E
E
X
ST
A
A
T
US
X
1
3
9
4
B
I
E
E
E
1
3
9
4
A
I
E
E
E
1
3
9
4
A
I
E
E
E
ASI OU
I
E
E
E
1
3
9
4
A
T
ASI
O
UT
I
1
3
9
4
A
ASI OUT
HD
E
E
E
ASI
O
UT
ASI OUT
Channel
.
.
.
.
.
.
ASI OUT
AC
Power
Cord
ASI Out
from HCS6600
Power Outlet
(120V 60Hz AC)
NTSC Monitor
RF
Room
Distribution
Grid
Rec
eiv
er
Modulator
Room
Rec
eiv
er
Combiner
Upconverter
Room
Rec
eiv
er
Room
Note: This diagram shows setup connections
where a unique feature card is NOT installed
in the card frame CONTROLLER slot.
Rec
eiv
er
206-4119
10
System Setup
Typical HCS6600 System Installation & Test
(see also Typical Setup Flow Chart on page 12)
1. Verify that the Cable TV STB receiver is set
up and functioning (i.e., check that the STB is
connected to an NTSC monitor [for tuning pur-
poses], that it is powered up, that initialization
is complete, and that the NTSC monitor is
displaying the default channel properly—refer
to the STB documentation).
5. If your installation includes a separate modula-
tor and upconverter, connect an RF coaxial
cable between IF OUT on the modulator and
IF IN on the upconverter, and then check the
modulator and upconverter for correct settings
(QAM type, channel number, etc.).
6. Repeat steps 1 to 5 for each of the Cable TV
STB/transcoder pairs.
2. On the Cable TV STB, tune to the appropri-
ate channel using the controls on the front
panel or the IR remote control.
7. Plug in power to the CodePlus card frame
containing the newly installed HCS6600
card(s). The green Status LED will blink at an
approximately 1 Hz rate while the HCS6600
card boots up. The boot-up process for an
HCS6600 may take up to two minutes, and
there is no ASI output (if applicable) during
boot-up.
3. Connect the IEEE-1394 cable between the
Cable TV STB and the HCS6600 IEEE-
1394A port.
4. Perform one of the following per your
installation:
• If the HCS6600 will NOT be used with a
unique feature card in the card frame
CONTROLLER slot, connect a 75 ohm
BNC-to-BNC coaxial cable between ASI
OUT on the transcoder and ASI IN on the
modulator. Then, continue with step 5.
When the boot-up is complete, the green
Status LED will be lit continuously.
8. If applicable, connect the RF output on the
upconverter to the combiner.
9. Check one or more room receivers to make
sure all channels are properly tuned,
mapped, and operating.
Note: The BNC cable must be less
than 30 feet (9.2 meters) in length.
• If the HCS6600 will be used with a unique
feature card in the CONTROLLER slot, the
cable to the ASI OUT port may not be
required. Refer to the Installation & Setup
Guide for the feature card for further instruc-
tion before you continue this setup procedure.
206-4119
11
System Setup (Cont.)
Typical Setup Flow Chart for a Single HD Channel
Cable TV Service Feed
RF Cable
RF In
Access
Card
Cable TV
STB
A/V
Cables
(for monitor only)
1394 Out
1394 In
HCS6600
Combiner
ASI Out
ASI
IF In
ASI In
VSB or QAM
Modulator
NTSC
Monitor
DTV
RF
Cable
RF
Coaxial
Cable
Upconverter
IF Out
RF Out
Note: This diagram shows setup connections
where a unique feature card is NOT installed
in the card frame CONTROLLER slot.
206-4119
12
Configuration Options
The HCS6600 contains several internal registers for different configuration options. These can either
be left at their default values or configured by the user.
There are two methods available for configuration purposes:
• Service Port Method
• Controller Card Method
This document describes configuration procedures using the Service Port Method, which requires that
you connect a PC directly to the transcoder Service Port. For configuration procedures using the
Controller Card Method, refer to the Installation & Setup Guide for the feature card installed in the card
frame CONTROLLER slot.
You now have access to the HCS6600 configu-
ration Main Menu. Refer to the following sections
for information on user-configurable options.
Connect a PC to the HCS6600 Service
Port and Access the HCS6600 Main Menu
1. Follow the directions in the Installation and
Test sections of this manual. The Cable TV
STB and the HCS6600 must be installed and
operating before you proceed.
Disable the Content Advisory Descriptor
For legacy systems using LST5600 Set-back
Box receivers, it is necessary to disable the
Content Advisory Descriptor in the PMT of the
HCS6600’s Transport Stream output. All other
products will operate normally with the Content
Advisory Descriptor enabled. The default setting
is Content Advisory Descriptor Enabled.
2. Connect the PC to the HCS6600 Service Port
using the FTDI TTL-USB cable (P/N TTL-
232R-5V-AJ):
• Plug the USB end of the cable into an open
USB port on your PC. If necessary, install
the device driver.
Note: Disabling the Content Advisory
Descriptor will disable the Parental
Control (V-Chip) feature of all room receiv-
ers for this channel.
• Plug the other end of the cable into the
Service Port jack on the HCS6600 front
panel.
3. Using HyperTerminal or an equivalent terminal
emulation program on the PC, configure the
COM port as follows:
Use the following procedure if you wish to dis-
able V-Chip.
1. Connect your PC to the HCS6600 Service
Port, and access the Main Menu as described
previously.
• Baud = 115200
• Data bits = 8
• Parity = None
• Stop bits = 1
2. With the Main Menu on display, type the
number corresponding to the Toggle Content
Advisory option, and press Enter.
• Flow Control = None
The system will print out the new state of the
Content Advisory Descriptor option. This state
will be stored in non-volatile storage and remain
in that state until changed by a user.
Then, initiate communication with the
HCS6600.
4. Press Enter to refresh the menu display in
the terminal.
206-4119
13
Configuration Options (Cont.)
Change or Renew the Pro:Idiom
Encryption Key
Note: The process of updating the
encryption key will synchronize the
decryption key in any receiver tuned to this
card's output. If the target receiver is turned
off or viewing a different card, the synchroni-
zation will not occur, and the output will be
scrambled. Ensure that all encrypters and
decrypters in a system are synchronized to
the same key.
The Pro:Idiom encrypter built into the HCS6600
contains a default encryption key. When first
installed, the HCS6600 will use this key to
encrypt content.
Note: In order for a Pro:Idiom
encrypted channel to be displayed,
the following conditions are required:
• The receiver must contain a Pro:Idiom
decrypter.
View the Pro:Idiom Key Checksum
Use the following procedure if you wish to dis-
play the Pro:Idiom Key checksum.
• The MPI control card in the receiver must
be configured to allow decryption of the
desired channel.
1. Connect your PC to the HCS6600 Service
Port, and access the Main Menu as described
previously.
If it becomes necessary to change or renew the
encryption key, use the following procedure.
2. With the Main Menu on display, type the num-
ber corresponding to the Read PI Key
Checksum option, and press Enter.
1. Connect your PC to the HCS6600 Service
Port, and access the Main Menu as described
previously.
The system will display the following:
2. With the Main Menu on display, type the
number corresponding to the Setup PI
option, and press Enter.
PI key checksum is xxxxxxxxxx
where xxxxxxxxxx identifies the set of Pro:Idiom
Key files installed on the transcoder.
3. The system will request a key file. Transfer
the new Pro:Idiom key file using Xmodem
protocol.
Note: All transcoder cards in the card
frame must have the same Pro:Idiom
Key files installed.
For example, in HyperTerminal, select
Transfer and then Send File.... In the Send
File window, enter or select the appropriate
Pro:Idiom key file in the Filename field, and
select Xmodem in the Protocol field.
View System Information
Use the following procedure if you wish to dis-
play system data, including HCS6600 hardware
and software information.
The system will then print out the result of the
update process. Note that the new key will be
stored in non-volatile storage regardless of pro-
cess results.
1. Connect your PC to the HCS6600 Service
Port, and access the Main Menu as described
previously.
(Continued on next page)
206-4119
14
Configuration Options (Cont.)
(Continued from previous page)
1. Connect your PC to the HCS6600 Service
Port, and access the Main Menu as described
previously.
2. With the Main Menu on display, type the
number corresponding to the System Info
option, and press Enter.
2. With the Main Menu on display, type the
number corresponding to the Update
Firmware option, and press Enter.
The system will display a System Information
banner that contains important information
3. The system will request a configuration (.cfg)
about the HCS6600, including the unit serial num-
ber, hardware ID (firmware version), and software
version. LG suggests that you record this infor-
mation for future reference. If you find it neces-
sary to call customer service or engineering sup-
port, please have this information available.
file. Transfer the new configuration file using
Xmodem protocol.
For example, in HyperTerminal, select
Transfer and then Send File.... In the Send
File window, enter or select the appropriate
configuration file in the Filename field, and
select Xmodem in the Protocol field.
Reset the HCS6600
4. Upon receipt of the configuration file, the
system will request a package (.pkg) file.
Transfer the package file using Xmodem
protocol.
Use the following procedure if you wish to reset
the HCS6600.
1. Connect your PC to the HCS6600 Service
Port, and access the Main Menu as described
previously.
This process may take several minutes;
please be patient. When the process is com-
plete, the system will report success or failure
of the firmware installation.
2. With the Main Menu on display, type the
number corresponding to the Reset option,
and press Enter.
5. Repeat steps 1 to 4 of this procedure for
each HCS6600 card whose firmware you
wish to update.
The system resets the HCS6600. During the
reset process, several pages of status and diag-
nostic messages may be displayed. After reset,
the HCS6600 resumes normal operation, and
the system displays the System Information ban-
ner and Main Menu.
6. Upon successful installation(s), power cycle
the system: Unplug the power cord of the card
frame for 15 seconds; then plug it in again.
Update HCS6600 Firmware
Use the following procedure if you wish to
update HCS6600 firmware.
Note: If you are not sure of the current firmware
version, LG recommends that you view and
record the System Information (see procedure
above) before you initiate the firmware update.
206-4119
15
Troubleshooting
Many problems can be corrected with a simple reset of the Cable TV STB and/or the HCS6600.
Running the system test on the Cable TV STB receiver can also help you diagnose and solve many
common problems.
If you experience image freezes, audio freezes, or a blank screen, or the system won’t respond to a
front panel button or remote control key presses, try one of these:
• Remove and reinsert the cable access card in the Cable TV STB.
• If your STB has a RESET button, press it, and then wait for program guide information to be
acquired.
• Unplug the power cord of the STB for 15 seconds; then plug it in again.
• Press the RESET button on the HCS6600 card to reboot it.
• Unplug the power cord of the CodePlus card frame for 15 seconds; then plug it in again.
Equipment Setup Review
• Make sure all connectors and connections are tight and secure on all entertainment system
components.
• Check the IEEE-1394 connection.
• Ensure that the access card is installed, is up-to-date, and has been authorized by the Cable
Service provider.
• Check that the batteries in the remote control are fresh and that the remote mode selector switch
is set on "CATV." Note that only one Cable TV STB should be ON at a time.
Status LED
The green Status LED on the HCS6600 front panel provides general information about the operating
condition of the transcoder. Observe the Status LED, and refer to the following table:
Status LED Behavior
Slow Blinking
Operating Status
System Booting
Rapid Blinking
Ready for Input
Continuously On
Continuously Off
Normal Operation
Fault Condition, No Output
206-4119
16
Specifications
Dimensions
Height:
3U (130.20 mm)
Width:
Depth:
Weight:
1.102362 inches (28.00 mm)
9.055118 inches (230.00 mm)
0.485016 pounds (0.22 kgrms) Est.
Environmental Storage Conditions
Temperature: -20° to 70° degrees Celsius
-4° to 158° degrees Fahrenheit
Humidity:
95% non-condensing
Environmental Operating Conditions
Temperature: 0° to 40° degrees Celsius
32° to 104° degrees Fahrenheit
Humidity:
95% non-condensing
Electrical
DC Input:
+12V DC @ 0.4 Amps
75 Ohms
800 mv
Impedance at ASI Out jack:
Active Output Level at ASI Out jack:
IEEE-1394 Input:
IEEE-1394a-2000
Note: Design and specifications subject to change without prior notice.
206-4119
17
Document Revision History / Notes
Document Revision History
Date
Description
February 2010
Revision A: New Document
Products page, select Head End Systems, then CodePlus™ Transcoder Series, then Cable TV
Modular Systems, then the applicable CodePlus series card frame, then HCS6600. Click the
Downloads & Images tab on the HCS6600 page, and select the required document from the
Downloads list.
Notes
206-4119
18
LG HCS6600 Cable Transcoder Warranty
Broadcast Products
Welcome to the LG family! We believe that you will be pleased with your new HCS6600 Cable TV Transcoder. Please read
this warranty carefully, it is a “LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal
rights, and you may also have other rights that vary from state-to-state within the U.S.A.
LG’s RESPONSIBILITY
Warranty Term
Parts
One year parts and labor from date of purchase or delivery date.
New or remanufactured replacements for factory-defective parts may be used. Such replacement parts are warranted for
the remaining portion of the original warranty period.
Warranty Service
Not Covered
Warranty service is provided at LG. Customer pays for shipping charges to LG; LG pays for return shipping charges to
return HCS6600 to customer. Call 1-888-865-3026 for further information.
This warranty covers manufacturing defects and does not cover installation, adjustment of customer controls, installation or
repair of antenna systems, cable converters or cable company-supplied equipment; it also does not cover damage due to
misuse, abuse, negligence, acts of God or other causes beyond the control of LG. Any alteration of the product after man-
ufacture voids this warranty in its entirety.
This warranty does not cover any missing or stolen access cards.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND LG
SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND,
INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THIS PRODUCT. SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY
TO YOU.
OWNER’S RESPONSIBILITY
Effective Warranty Date Warranty begins on the date of delivery of the HCS6600.
For your convenience, keep the dealer’s dated bill of sale or delivery ticket as evidence of the purchase date.
Installation Guide
Read the Installation and Setup Guide carefully so that you will understand the operation of the HCS6600 and how to
adjust the controls.
Antenna
Reception problems caused by inadequate antenna or faulty antenna connections are the owner’s responsibility.
Warranty Service
For warranty service information, call 1-888-865-3026. Parts and service labor that are LG’s responsibility (see above)
will be provided without charge. Other service is at the owner’s expense. If you have any problem in obtaining satisfactory
warranty service, call 1-888-865-3026.
You must provide the model number, serial number and date of purchase or date of original installation.
For Customer Support/Service, please call:
1-888-865-3026
CodePlus is a trademark of LG Electronics U.S.A., Inc. All other trademarks or
registered trademarks are the property of their respective owners.
206-4119
Revision A
Copyright 2010, LG Electronics U.S.A., Inc.
|